Shopping Cart

You do not have any products in your shopping cart yet.


Welcome back !

eMail Address:

New Products

Fender Audio 1270P Powered Two-Way Coaxial Molded Enclosure Monitor

Fender Audio 1270P Powered Two-Way Coaxial Molded Enclosure Monitor

$192.00

Currencies

JOEMEEK SixQ Channel Strip

JOEMEEK SixQ Channel Strip
$359.00
Manufacturer's Code:SIXQ

In Stock - This product usually ships next day.

A serious discount available for this item - details can be found at checkout.

The Joemeek sixQ packs a wealth of features into a single rack space studio channel. A single channel mic pre, based on our high quality Burr-Brown IC, three bands of highly musical EQ, and our signature optical compressor make for a highly capable recording instrument. With a front panel instrument input. Output either analog or digitally directly to your sound card or DAW for a warm, musical analog sound - just what you've been looking for!

Digital Interface

The Joemeek Digital Audio Interface provides high quality digital audio outputs. The digital audio outputs are compatible with most digital recorders, as well as Digital Audio Workstations and mixers. S/PDIF format is available from the optical and RCA phono connectors.

The Joemeek Digital Interface has highly stable onboard master clocks for low-jitter, hi-fi results. Internal sample rates of 44.1kHz, 48kHz, 88.2kHz or 96kHz are selected by means of rear panel switches. 44.1kHz is the standard used for audio CD's, while 48kHz and 96kHz are widely used in recording studios. In general, the higher the sample rate, the better the audio fidelity, but the more disk space is required for the recording. For example, recording at 96kHz requires twice as much storage as 48kHz. Consult the manual of your recorder or DAW as to what sample rates it will accommodate.

Specifications

Input impedances:
Mic: 1.2kohm; Line: 20kohm
Pre-amp overall gain:
10dB to 60dB (variable)
Common mode rejection:
70dB
Equivalent input noise:
-128.5dBu (unweighted)
Distortion:
 
0.001% (below Compressor threshold)
Frequency response:
15Hz to 70kHz (-3dB)
Maximum input before clipping:

Mic: +21dBu; Line: +45dBu

Headroom before clipping:
+21dBu
Compressor threshold:

∞dBu to -20dBu (variable)

Compressor ratio:
1:1 to 10:1 (variable)
Compressor attack time:

1 msec to 100 msec (adaptive)

Compressor release time:
0.1 sec to 3 sec (adaptive)
Nominal output levels:

+4dBu/-10dBv

Output impedance:
75ohm
Output Level switch:

12dB attenuation

Noise Floor:
-85dBu (typical, with ~40dB mic gain)
VU Meter:

Analogue movement

Power supply:
115V / 230V ac mains, 50/60Hz
Power consumption:

30W

Mechanical:
482W x 88H x 220D (overall)
Weight:

3 kilos

High Pass Filter:
12dB per octave cut below 80Hz
EQ Boost & Cut:

+/-15dB (zero phase-shift bell response)

LF Frequency :

40Hz to 650Hz variable

Mid Frequency :

300Hz to 5kHz variable

HMF Frequency :

1kHz to 6kHz variable

HF Frequency :

6kHz/12kHz switchable

EQ "Q"

0.9 (1.6 octaves

Digital Output Specifications

Sampling:
24 Bit
Sampling Rate:
44.1kHz, 48kHz, 88.2kHz or 96kHz selectable
Output Formats:
AES3 compliant (balanced), S/PDIF electrical, S/PDIF optical

 

 



 

 
Copyright © 2008 Digilake.com. All rights reserved.